Ariens Snow Blower Parts | Same Day Shipping (2024)

Ariens Snow Blower Shear Bolt

PartSelect Number PS9002923

Manufacturer Part Number 51001500

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Ariens Snow Blower Friction Wheel

PartSelect Number PS17016657

Manufacturer Part Number 09475300

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" difficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

Ariens Snow Blower Shear Bolt and Nut

PartSelect Number PS9000870

Manufacturer Part Number 52100100

This shear bolt and nut, also known as the shear bolt assembly, is sourced from the original manufacturer, and it is guaranteed to fit your snowblower. Each assembly includes one metal shear bolt and one metal nut, located at the connection point between the auger and gearbox/shaft. It is a safety mechanism designed to protect the snowblower auger from damage caused by sudden stops or excessive resistance. When the auger encounters a blockage or excessive load the shear bolt will break thereby preventing more severe damage to the gearbox. Once the bolt is sheared, it will need to be replaced. The bolt will also need to be replaced if it is bent or worn down, as a faulty shear bolt can result in damage to the auger, gearbox, and motor, as well as reduced equipment ability to throw snow, and increased safety risks. Use a socket or wrench to unthread the nut and remove the broken shear bolt. Align the new shear bolt with the mounting hole and secure it with the new nut. Note that this is a common repair and it is best to have several spare shear bolts and nuts on hand.

Ariens Snow Blower Pin-LOK .31 x 1.75

PartSelect Number PS8801947

Manufacturer Part Number 07053700

Ariens Snow Blower Clip, Snap

PartSelect Number PS8797281

Manufacturer Part Number 05700001

The Snap Clip is a silver, metal part used to prevent the wheels from falling off, by securing it to the axle. If broken or damaged it should be replaced, or the wheel may fall off.

Ariens Snow Blower Fuel Tank Cap - Red Plastic Vented Bayonet Style

PartSelect Number PS11835127

Manufacturer Part Number 52107500

Ariens Snow Blower Friction Wheel

PartSelect Number PS9249926

Manufacturer Part Number 03248300

This friction wheel, or disc, works in conjunction with a pulley system in your lawn equipment to propel your machine forward. It is a metal disc with a rubber ring around it, has an approximate inside diameter of 2.5 inches, and is commonly mounted onto the axle of your machine. When it is broken, you can visually identify cracks in or missing parts from the part, or excessive wear on the rubber ring. If you do not replace it, your equipment may struggle to move on slippery or uneven surfaces and lose traction. To remove the old friction wheel, start by turning off the engine and disconnecting the spark plug wire. Consult your user manual for instructions on accessing the wheel. You might need a wrench or socket to remove retaining bolts, screws, or clips. Keep in mind that the replacement part is sold individually since your machine may require more than one wheel, and they tend to wear out at the same time.

Ariens Snow Blower Shear Bolt

PartSelect Number PS9007730

Manufacturer Part Number 53200500

Ariens Snow Blower Runner

PartSelect Number PS9249396

Manufacturer Part Number 02483859

The Runner is a 6 x 3.5 inch, orange, metal part which is used to allow the snowblower to glide smoothly on the ground. It's installed using a wrench or socket, and its installation has been rated "Easy" by customers. If broken, the auger housing will drag on the ground and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part.

Ariens Snow Blower V-Belt -Traction Drive

PartSelect Number PS8802518

Manufacturer Part Number 07211200